Flooring Izjava o lastnosti Verzija 01.07.2013 Identifikacijska številka. 0208010402500000011008 Verzija št.. 01 EN 1504-2: 2004 08 0921 EN 13813: 2002 IZJAVA O LASTNOSTIH 0208010402500000011008 Declaration of performance 1. Tip izdelka: Enotna identifikacijska oznaka tipa proizvoda: 2. Tip, serijska ali zaporedna številka ali kateri koli drug element, na podlagi katerega je mogoče prepoznati gradbene proizvode, v skladu s členom 11(4): 3. Predvidena uporaba ali predvidene vrste uporabe gradbenega proizvoda v skladu z veljavno harmonizirano tehnično specifikacijo, kot jih predvideva proizvajalec: 4. Ime, registrirano trgovsko ime ali registrirana blagovna znamka in naslov proizvajalca v skladu s členom 11(5): 5. Kontaktni naslov: Po potrebi ime ali naslov pooblaščenega zastopnika, katerega pooblastilo zajema naloge, opredeljene v členu 12(2): 6. AVCP: Sistem ali sistemi ocenjevanja in preverjanja nespremenljivosti lastnosti (AVCP) gradbenega proizvoda, kot je določeno v CPR v Prilogi V: 7. Organ za tehnično ocenjevanje (hen): Za izjavo o lastnostih glede gradbenega proizvoda, za katerega velja harmoniziran standard: 8. Organ za tehnično ocenjevanje (ETA): Za izjavo o lastnostih glede gradbenega proizvoda, za katerega je bila izdana evropska tehnična ocena EN 13813:2002 359 N Saržna številka (Glej deklaracijo na izdelku) Dvokomponentni, žilavo elastični, barvni, poliuretanski zaporni premaz, ki ne porumeni. Kot abrazijsko odporna zaporna plast z visoko mehansko odpornostjo za posute sisteme in kot premaz za premoščanje razpok pri izdelavi industrijskih tlakov. Še posebej primeren za avtomobilska parkirišča, nakladalne rampe, skladišča itd. Skladno s EN 13813 SR-B2,0-AR1-IR4 Sikafloor Kornwestheimer Str. 103-107 70439 Stuttgart, Germany Glej poglavje 4. Sistem 4 - Ni pomembno 1/5
9. Navedene lastnosti Bistvene značilnosti Lastnost Testni standard Sproščanje korozivnih substanc(estrih iz SR EN 13813 umetnih snovi): Odpornost na obrabo: AR1 1) EN 13892-4 Sprijemna trdnost: B2,0 EN 13892-8 Udarna trdnost: IR4 EN ISO 6272 Izolacija telesnega zvoka: NPD EN ISO 140-1 Absorbcija zvoka: NPD EN ISO 354 Požarne lastnosti: 2) E fl EN 13501-1 Prepustnost za vodno paro: NPD EN ISO 7783-1 Toplotna odpornost: NPD EN 12664 Kemijska odpornost: NPD EN 13529 Harmonizirane tehnične specifikacije EN 13813 1) Minimalna klasifikacija, obrnite se na individualno testno poročilo/certifikat. 2) V skladu s Sklepom Komisije 2010/85/EU z dne 9. februarja 2010 izdelek izpolnjuje razred odziva na ogenj E / Efl brez nadaljnjega preskušanja 2/5
EN 1504-2:2004 1. Tip izdelka: Enotna identifikacijska oznaka tipa proizvoda:: 2. Tip, serijska ali zaporedna številka ali kateri koli drug element, na podlagi katerega je mogoče prepoznati gradbene proizvode, v skladu s členom 11(4): 3. Predvidena uporaba ali predvidene vrste uporabe gradbenega proizvoda v skladu z veljavno harmonizirano tehnično specifikacijo, kot jih predvideva proizvajalec: 4. Ime, registrirano trgovsko ime ali registrirana blagovna znamka in naslov proizvajalca v skladu s členom 11(5): 5. Kontaktni naslov: Po potrebi ime ali naslov pooblaščenega zastopnika, katerega pooblastilo zajema naloge, opredeljene v členu 12(2): 6. AVCP: Sistem ali sistemi ocenjevanja in preverjanja nespremenljivosti lastnosti (AVCP) gradbenega proizvoda, kot je določeno v CPR v Prilogi V: 7. Organ za tehnično ocenjevanje (hen): Za izjavo o lastnostih glede gradbenega proizvoda, za katerega velja harmoniziran standard: 8. Organ za tehnično ocenjevanje (ETA): Za izjavo o lastnostih glede gradbenega proizvoda, za katerega je bila izdana evropska tehnična ocena 359 N Saržna številka (Glej deklaracijo na izdelku) Dvokomponentni, žilavo elastični, barvni, poliuretanski zaporni premaz, ki ne porumeni. Kot abrazijsko odporna zaporna plast z visoko mehansko odpornostjo za posute sisteme in kot premaz za premoščanje razpok pri izdelavi industrijskih tlakov. Še posebej primeren za avtomobilska parkirišča, nakladalne rampe, skladišča itd. Principles 1, 2, 5, 6, 8 - methods 1.3, 2.2, 5.1, 6.1, 8.2 of EN 1504-2 Sikafloor Kornwestheimer Str. 103-107 70439 Stuttgart, Germany Glej poglavje 4 Sistem 2+ Sistem 3 0921 Priglašeni certifikacijski organ za kontrolo proizvodnje št. 0921 je izvedel začetno preveritev proizvodnega obrata in kontrole proizvodnje in izvaja redni nadzor, presojo in vrednotenje notranje kontrole proizvodnje ter izdaja certifikat o skladnosti notranje kontrole proizvodnje št. (FPC) 0921-CPR-2017 0767 Priglašeni certifikacijski organ za kontrolo MPA Dresden številka 0767 je izvedel določitev požarnega razreda na podlagi preiskušanja tipa po sistemu 3 izdal poročilo o preiskusu: 2007-B-0181/9 Ni pomembno 3/5
9. Navedene lastnosti Bistvene značilnosti Lastnost Testni standard Nevarne snovi NPD Odpornost na obrabo (Taber test) 1) : < 3000 mg EN ISO 5470-1 Prepustnost na CO 2 : s D 50 m EN 1062-6 Prepustnost za vodno paro: Class III EN ISO 7783-1 Kapilarna vpojnost in prepustnost za vodo: w<0,1 kg/(m 2 x h 0,5 ) EN 1062-3 Obstojnost na močne kemijske Razred I EN 13529 obremenitve: 2) : Udarna trdnost: Razred I EN ISO 6272-1 Sprijemna trdnost pri preskusu na odtrganje: 2,0 (1,5) 3) N/mm² EN 1542 Požarne lastnosti: Razred E fl EN 13501-1 Linearno krčenje: NPD EN 12617-1 Tlačna trdnost: NPD EN 12190 Koeficient toplotnega raztezka: NPD EN 1770 Cross cut: NPD EN ISO 2409 Toplotna izolacija NPD EN 13687 Odpornost na temperaturne šoke: NPD EN 13687-5 Kemična odpornost: NPD ISO 2812-1 Premoščanje razpok: NPD EN 1062-7 1) Poleg zahteve po EN 13813, morajo biti izpolnjeni 2) Prosimo, poglejte si karto kemijske odpornosti za Sikafloor -proizvode. 3) Vrednost v oklepaju je najnižja sprejemljiva vrednost. Harmonizirane tehnične specifikacije EN 1504-2: 2004 0921 Plant 1008 08 0208010402500000011008 EN 1504-2:2004 4/5
10. Lastnosti proizvoda Lastnosti proizvoda, navedenega v točki 1 in 2, so v skladu z navedenimi lastnostmi iz točke 9. Za izdajo te izjave o lastnostih je odgovoren izključno proizvajalec, naveden v točki 4: Podpisal za in v imenu proizvajalca: Jochen Grotzinger Martin Rolfes Dr. Heinz Ephardt Stuttgart, 1. Julij 2013 Ekološke, zdravstvene in varnostne informacije (REACH Za informacije in nasvete o varnem rokovanju, skladiščenju in odlaganju kemijskih proizvodov naj si uporabniki pridobijo zadnji varnostni list, kjer so navedeni fizikalni, ekološki, toksikološki in ostali podatki o varnosti za obravnavani proizvod. Pravno sporočilo: Informacija in še posebej priporočila, ki se nanašajo na rabo in končno uporabo Sika proizvodov, so dani v dobri veri, ki temelji na Sikinem dosedanjem znanju in izkušnjah v zvezi s proizvodi, če so pravilno skladiščeni, če se z njimi pravilno ravna in če so uporabljeni v normalnih pogojih. V praksi so razlike v materialih, podlagah in dejanskih pogojih na gradbišču take, da iz te informacije ali katerihkoli pisnih priporočil ali iz katerihkoli drugih podanih nasvetov ne moremo jamčiti tržljivosti ali primernosti za nek poseben namen, niti ne moremo prevzeti nobene odgovornosti, ki izvira iz kateregakoli zakonitega odnosa. Lastninske pravice tretjih se morajo spoštovati. Vsa naročila podležejo našim sedanjim prodajnim in dobavnim pogojem. Porabniki bi morali vedno pregledati najnovejši izvod tehničnega lista za zadevni proizvod, kopijo katerega dostavimo na zahtevo. Sika d.o.o. Telefon 01.580.95.34 Prevale 13 Fax 01.580.95.33 1236 Trzin www.sika.si 5/5
Flooring Declaration of Performance Edition 01.07.2013 Identification no.0208010402500000011008 Version no. 01 EN 1504-2: 2004 08 0921 EN 13813: 2002 DECLARATION OF PERFORMANCE 0208010402500000011008 Declaration of performance 1. Product Type Unique identification code of the product-type: 2. Type batch or serial number or any other element allowing identification of the construction product as required under Article 11(4): 3. Intended use or uses of the construction product, in accordance with the applicable harmonised technical specification, as foreseen by the manufacturer: 4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required under Article 11(5): 5. Contact Address Where applicable, name and contact address of the authorized representative whose mandate covers the tasks specified in Article 12(2): 6. AVCP System or systems of assessment and verification of constancy of performance (AVCP) of the construction product as set out in CPR, Annex V: 7. Notified body (hen) In case of the declaration of performance (DoP) concerning a construction product covered by a harmonised standard: EN 13813:2002 359 N batch no. refer to packaging 2-part, tough-elastic, coloured, nonyellowing, polyurethane seal coat.. Abrasion resistant seal coat with high mechanical resistance for broadcast systems with crack-bridging properties in industrial flooring. Particularly suitable for car park decks, garage floors and bridges etc. According to EN 13813 SR-B2,0-AR1-IR4 Sikafloor Kornwestheimer Str. 103-107 70439 Stuttgart, Germany not relevant (see 4) System 4-8. Notified body (ETA) In case of the declaration of performance concerning a construction product for which a European Technical Assessment (ETA) has been issued: not relevant 1/5
9. Declared performance Essential characteristics Release of corrosive substances(synthetic Resin Screed): Performance Test Standard SR EN 13813 Abrasion Resistance: AR1 1) EN 13892-4 Harmonised technical specification Bond strength: B2,0 EN 13892-8 Impact resistance: IR4 EN ISO 6272 Sound insulation: NPD EN ISO 140-1 Sound absorption: NPD EN ISO 354 Reaction to fire: E fl 2) Permeability to water vapour: EN 13501-1 NPD EN ISO 7783-1 Thermal resistance: NPD EN 12664 EN 13813 Chemical resistance: NPD EN 13529 1) Min. classification, please refer to the individual test certificate. 2) According to Commission Decision 2010/85/EU of 9 February 2010 the product fulfils the reaction-to-fire performance class E/Efl without further testing Plant 1008 08 0208010402500000011008 EN 13813:2002 2/5
EN 1504-2:2004 1. Product Type Unique identification code of the product-type: 2. Type batch or serial number or any other element allowing identification of the construction product as required under Article 11(4): 3. Intended use or uses of the construction product, in accordance with the applicable harmonised technical specification, as foreseen by the manufacturer: 4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required under Article 11(5): 5. Contact Address Where applicable, name and contact address of the authorized representative whose mandate covers the tasks specified in Article 12(2): 6. AVCP System or systems of assessment and verification of constancy of performance (AVCP) of the construction product as set out in CPR, Annex V: 7. Notified body (hen) In case of the declaration of performance (DoP) concerning a construction product covered by a harmonised standard: 8. Notified body (ETA) In case of the declaration of performance concerning a construction product for which a European Technical Assessment (ETA) has been issued: 359 N batch no. refer to packaging 2-part, tough-elastic, coloured, nonyellowing, polyurethane seal coat.. Abrasion resistant seal coat with high mechanical resistance for broadcast systems with crack-bridging properties in industrial flooring. Particularly suitable for car park decks, garage floors and bridges etc. Principles 1, 2, 5, 6, 8 - methods 1.3, 2.2, 5.1, 6.1, 8.2 of EN 1504-2 Sikafloor Kornwestheimer Str. 103-107 70439 Stuttgart, Germany not relevant (see 4) System 2+ System 3 0921 Notified factory production control certification body No. 0921 QDB performed the initial inspection of the manufacturing plant and of factory production control and the continuous surveillance, assessment and evaluation of factory production control under system 2+ and issued the certificate of conformity of the factory production control (FPC) 0921-CPR-2017 0767 Notified Body MPA Dresden number 0767 performed the determination of reaction to fire class on the basis of type testing under system 3 and issued test report: 2007-B-0181/9 not relevant 3/5
9. Declared performance Tested systems: Sikafloor-350 N Elastic, Sikafloor-375 and Essential characteristics Dangerous substances Abrasion resitance (Taber test) 1) : Performance NPD Test Standard < 3000 mg EN ISO 5470-1 Permeability to CO 2: s D 50 m EN 1062-6 Permeability to water vapour: Capillary absorption and permeability to water: Resistance to severe chemical attack 2) : Class III EN ISO 7783-1 w<0,1 kg/(m 2 x h 0,5 ) EN 1062-3 Class I EN 13529 Impact resistance: Class I EN ISO 6272-1 Adhesion strength by pull-off test: 2,0 (1,5) 3) N/mm² EN 1542 Reaction to fire: Class E fl EN 13501-1 Linear shrinkage: NPD EN 12617-1 Compressive strength: NPD EN 12190 Coefficient of thermal expansion: NPD EN 1770 Cross cut: NPD EN ISO 2409 Thermal compatibility: NPD EN 13687 Resistance to thermal shock: NPD EN 13687-5 Chemical resistance: NPD ISO 2812-1 Crack bridging ability: NPD EN 1062-7 1) Additionally the requirements according to EN 13813 have to be fulfilled 2) Please refer to the Sikafloor Chemical Resistance Chart 3) The value in brackets is the lowest accepted value of any reading. Harmonised technical specification EN 1504-2: 2004 0921 Plant 1008 08 0208010402500000011008 EN 1504-2:2004 4/5
10. Declaration The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 9.This declaration of performance (DoP) is issued under the sole responsibility of the manufacturer identified in point 4. Signed for and on behalf of the manufacturer by: Jochen Grötzinger Martin Rolfes Dr. Heinz Ephardt Research and development Marketing Quality control Stuttgart, 1. Juni 2013 Ecology, Health and Safety Information (REACh) For information and advice on the safe handling, storage and disposal of chemical products, users shall refer to the most recent Safety Data Sheet (SDS) containing physical, ecological, toxicological and other safety related data. Legal note: This information is given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. In practice, the differences in materials, substrates and actual site conditions are such that no warranty in respect of merchantability or of fitness for a particular purpose, nor any liability arising out of any legal relationship whatsoever, can be inferred either from this information, or from any written recommendations, or from any other advice offered. The user of the product must test the product s suitability for the intended application and purpose. Sika reserves the right to change the properties of its products. The proprietary rights of third parties must be observed. All orders are accepted subject to our current terms of sale and delivery. Users must always refer to the most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request. Telefone +49 (0) 7 11 80 09-0 Kornwestheimer Str. 103-107 Fax +49 (0) 7 11 80 09-321 70439 Stuttgart www.sika.de 5/5